Making a Plastic Water Bottle Bong is actually easier than you might have thought. All you really need to do is put your mouth over the end of the bottle, place your thumb over the other end, and light up!
Method 1: Plastic Bottle Bong
Making a bong out of a plastic water bottle is probably the easiest way to make a bong. All you need is a plastic water bottle, a sharp knife, and some tape.
First, take the bottom off of the water bottle. Then, cut a hole in the side of the bottle near the top. The hole should be big enough to fit your mouth over.
Next, put your mouth over the hole and suck the air out of the bottle. This will create suction. Then, put your thumb over the hole and release the suction. The result should be a small stream of water shooting up into the air.
Finally, put your mouth over the hole again and suck the water back into the bottle. Congratulations! You’ve just made a plastic water bottle bong!
Method 2: Plastic Bottle Bong with Straw
A plastic water bottle bong with a straw is also a great way to make a bong. All you need is a plastic water bottle, a straw, and some tape.
To make the bong, start by cutting the bottom off of the plastic water bottle. Next, cut a small hole in the side of the bottle near the top. This will be where you insert the straw.
Once the hole is cut, insert the straw into it and secure it in place with tape. Make sure that the tape seals the straw tightly so that no air can escape.
Now, fill the bottle with water, making sure that the water level is below the level of the hole you cut for the straw. Put your mouth on the top of the bottle and suck on the straw to get a hit.
Method 3: Plastic Bottle Pipe
If you don’t have a bong or pipe handy, you can fashion one out of a plastic water bottle. This is probably the quickest and easiest way to make a bong. All you need is a plastic water bottle, a pen or pencil, and some aluminum foil.
First, take the water bottle and remove the cap. Then, use the pen or pencil to poke a hole in the side of the bottle, near the bottom. The hole should be big enough to fit the bowl of your aluminum foil pipe.
Next, take the aluminum foil and shape it into a bowl. Make sure that the bowl is big enough to cover the hole you just made in the water bottle. Once you have made your foil bowl, put it over the hole in the water bottle and press it down so that it’s snug.
Now it’s time to smoke! Put your weed in the bowl of the aluminum foil pipe and light it up. As you inhale, slowly start to pull up on the water bottle so that air can get through and create suction. This will cause smoke to fill up the water bottle. Keep pulling until all of the smoke has been cleared from the bowl; then remove the bowl and inhale deeply from the mouthpiece of the water bottle bong!
Method 4: Plastic Bottle Alcohol Inhaler
If you want to make a bong out of a plastic water bottle, one option is to use an alcohol inhaler. This is a simple process that only requires a few supplies.
You will need:
-A plastic water bottle
-An alcohol inhaler
-A small drill bit
-A knife or scissors
Instructions:
1. Cut a small hole in the bottom of the plastic water bottle. This will be for the mouthpiece.
2. Drill a small hole in the side of the bottle near the top. This will be for the air intake.
3. Insert the mouthpiece into the hole in the bottom of the bottle.
4. Insert the alcohol inhaler into the hole in the side of the bottle.
5. Enjoy your new bong!
Method 5: Plastic Bottle Dip Bowl
If you want to get creative with your bong, you can try making a plastic water bottle bong. This is a simple way to make a bong and all you need is a plastic water bottle and some tape.
To make a plastic water bottle bong, start by taking the cap off of the water bottle. Then, use a knife to make a small hole in the side of the bottle. Next, take a piece of tubing and insert it into the hole. Secure the tubing in place with tape.
Now, fill the bottle with water, leaving about an inch of space at the top. Put the cap back on the bottle and screw it on tightly. Finally, take your bowl piece and insert it into the tubing. Now you’re ready to smoke!
Method 6: Plastic Bottle Gatorade bottle bong
If you don’t have a gatorade bottle on hand, any plastic water bottle will do. Just make sure it’s clean!
1. Poke a hole in the bottom of the bottle with a pen or pencil. The hole should be about the size of a dime.
2. Cover the hole with your thumb and fill the bottle with water about halfway up.
3. Put the bowl of your bong onto the bottle and screw it on tightly.
4. Light your weed and place the mouthpiece of the bong to your lips.
5. Take your thumb off of the hole at the bottom of the bottle and inhale deeply!
Method 7: Cigarette Filter and Drinking Straw
Cigarette filters and drinking straws can be used to make a plastic water bottle bong. First, take a drinking straw and cut it in half. Next, take a cigarette filter and cut it in half. Then, put the two halves of the straw over the mouth of the water bottle and secure them with tape. Finally, put the two halves of the cigarette filter over the end of the straws and secure them with tape. Your bong is now ready to use!